A Self‐Assembled Superhydrophobic Electrospun Carbon–Silica Nanofiber Sponge for Selective Removal and Recovery of Oils and Organic Solvents

An oil spill needs timely cleanup before it spreads and poses serious environmental threat to the polluted area. This always requires the cleanup techniques to be efficient and cost‐effective. In this work, a lightweight and compressible sponge made of carbon–silica nanofibers is derived from electrospinning nanotechnology that is low‐cost, versatile, and readily scalable. The fabricated sponge has high porosity (>99 %) and displays ultra‐hydrophobicity and superoleophilicity, thus making it a suitable material as an oil adsorbent. Owing to its high porosity and low density, the sponge is capable of adsorbing oil up to 140 times its own weight with its sorption rate showing solution viscosity dependence. Furthermore, sponge regeneration and oil recovery are feasible by using either cyclic distillation or mechanical squeezing.     

9,10‐Diaminoanthracenes Revisited: The Influence of N‐Substituents on Their Electronic States

The electronic and molecular structures of 9,10‐diamino‐substituted anthracenes with different N‐substituents have been re‐examined. In particular, different N‐substituents influence both the electronic and molecular structures of the oxidized species of 9,10‐diaminoanthracenes. The anthrylene moiety of 9,10‐bis(N,N‐di(p‐anisyl)amino)anthracene retains its planarity during the course of two successive one‐electron oxidations, whereas 9,10‐bis(N,N‐dimethylamino)anthracene and 9,10‐bis(N‐p‐anisyl‐N‐methylamino)anthracene undergo a substantial structural change to a butterfly‐like structure through a two‐electron oxidation process. The structural changes observed for the oxidized states are ascribed to significant differences in the frontier molecular orbitals of the above‐mentioned three kinds of 9,10‐diaminoanthracenes due to different extents of mixing between the amine‐localized and anthrylene‐localized orbitals.     

Development and validation of UHPLC‐MS/MS assay for rapid determination of a carvone Schiff base of isoniazid (CSB‐INH) in rat plasma: application to pharmacokinetic study

In this study, a fast UHPLC‐MS/MS method was developed and validated for the determination of a novel potent carvone Schiff base of isoniazid (CSB‐INH) in rat plasma using carbamazepine as an internal standard (IS). After a single‐step protein precipitation by acetonitrile, CSB‐INH and IS were separated on an Acquity BEH^TM C₁₈ column (50 × 2.1 mm, 1.7 µm) under an isocratic mobile phase, consisting of acetonitrile: 10 mM ammonium acetate (95:5, v/v), at a flow rate of 0.3 mL/min. Quantification was performed on a triple quadrupole tandem mass spectrometer in multiple reactions monitoring mode by using positive electrospray ionization source. The precursor to product ion transitions were set at m/z 270.08 → 79.93 for CSB‐INH and m/z 237.00 → 178.97 for IS. The proposed method was validated in compliance with US Food and Drug Administration and European Medicines Agency guidelines for bioanalytical method validation. The method was found to be linear in the range of 0.35–2500 ng/mL (r² ≥ 0.997) with a lower limit of quantification of 0.35 ng/mL. The intra‐ and inter‐day precision values were ≤12.0% whereas accuracy values ranged from 92.3 to 108.7%. In addition, other validation results were within the acceptance criteria and the method was successfully applied in a pharmacokinetic study of CSB‐INH in rats. Copyright © 2014 John Wiley & Sons, Ltd.     

Highly Selective Zeolite Topologies for Flue Gas Separation

The separation of carbon dioxide from flue gas is essential for the reduction of greenhouse gas emissions. In adsorptive methods, the challenge lies in the choice of suitable porous materials. Among all zeolite topologies, a number of adsorbents with pore dimensions in the range of the guest molecules were identified to allow an excellent separation by diffusion, and MRE and AFO zeolite topologies appear to be the best candidates based on equilibrium adsorption. Also, it was found that the behavior of this gas mixture in DFT and APD zeolites differed from the normal behavior.     

UHMWPE纤维的超临界CO_2辅助渗透预处理研究

利用Minitab软件设计实验,以超高分子量聚乙烯纤维(UHMWPE)为原料,研究了在不同的超临界CO_2流体状态下,处理压力、温度和时间等因素对三羟甲基丙烷三甲基丙烯酸酯(TMPTMA)渗入率的影响,确定了最佳因素设置范围;通过单因子实验优化了超临界CO_2处理工艺,并对经过电子束辐照的UHMWPE纤维凝胶含量和蠕变率进行了测试。研究结果表明:处理温度对TMPTMA的渗入率影响最大,其次为压力,时间的影响最小,确定了最优工艺条件为处理压力25MPa,温度80℃,时间30min;TMPTMA渗入率越高,电子束辐照后UHMWPE纤维的增感辐照交联效应和抗蠕变效果越好。     

硼原子掺杂对碳纳米管吸附Ne原子影响的第一性原理计算

采用基于第一性原理的密度泛函理论（DFT）和局域密度近似（LDA）方法，优化计算得到碳纳米管（CNT），硼原子取代碳原子及其吸附氖原子前后系统的几何结构，能量，电子能带和态密度。结果显示，碳纳米管的能带结构与石墨的层状几何结构相似，能量的变化只在kz=0和kz=0.5平面之间沿着c轴方向出现。B原子取代C原子使价带和导带分别分裂为两个和三个能带。对Ne原子的吸附使价带能量沿着c轴方向升高并导致Fermi面附近的态密度下降。Ne原子的吸附在谷位H最稳定，顶位A其次。C-C间σ键的弯曲使Ne原子吸附在桥位b1比桥位b2处更为稳定。Ne原子在管外的吸附均为放热过程，而管内则为吸热过程。结构分析表明Ne原子对C原子有排斥作用，对B原子却具有吸引作用。B原子取代C原子的位置略凸出于CNT的管壁之外，使Ne原子的吸附能增加。     

CL-20/TNT共晶炸药的分子动力学研究

运用分子动力学(MD)方法,选择凝聚态分子势能优化力场(COMPASS),对六硝基六氮杂异伍兹烷(ε-CL-20)、2,4,6-三硝基甲苯(TNT)晶体及其等摩尔比的CL-20/TNT混合炸药和共晶炸药进行不同温度下恒定粒子数等压等温(NPT)系综模拟研究.结果表明,CL-20/TNT共晶的内聚能密度(CED)和结合能随温度的升高逐渐减小;共晶的CED比混合炸药的大,结合能是混合炸药的2倍多,预示其稳定性明显增强.对相关函数和局部放大结构显示共晶中组分分子间作用主要来自TNT中H和CL-20中O以及CL-20中H和TNT中O之间形成的氢键.通过波动法求得的弹性力学性能结果表明,CL-20/TNT共晶的拉伸模量(E)、体积模量(K)和剪切模量(G)介于ε-CL-20和TNT晶体之间,且随温度的升高而下降,符合一般预期;但共晶炸药的柯西压(C12-C44,Cij弹性系数)、K/G和泊松比(ν)均比其组分炸药ε-CL-20和TNT高得多,预示该共晶具有异常高的延展性和弹性伸长,主要是二组分呈层状交替排列且之间存在较强相互作用所致.     

Regioselective Alkylative Carboxylation of Allenamides with Carbon Dioxide and Dialkylzinc Reagents Catalyzed by an N‐Heterocyclic Carbene–Copper Complex

The alkylative carboxylation of allenamide catalyzed by an N‐heterocyclic carbene (NHC)–copper(I) complex [(IPr)CuCl] with CO₂ and dialkylzinc reagents was investigated. The reaction of allenamides with dialkylzinc reagents (1.5 equiv) and CO₂ (1 atm.) proceeded smoothly in the presence of a catalytic quantity of [(IPr)CuCl] to afford (Z)‐α,β‐dehydro‐β‐amino acid esters in good yields. The reaction is regioselective, with the alkyl group introduced onto the less hindered γ‐carbon, and the carboxyl group introduced onto the β‐carbon atom of the allenamides. The first step of the reaction was alkylative zincation of the allenamides to give an alkenylzinc intermediate followed by nucleophilic addition to CO₂. A variety of cyclic and acyclic allenamides were found to be applicable to this transformation. Dialkylzinc reagents bearing β‐hydrogen atoms, such as Et₂Zn or Bu₂Zn, also gave the corresponding alkylative carboxylation products without β‐hydride elimination. The present methodology provides an easy route to alkyl‐substituted α,β‐dehydro‐β‐amino acid ester derivatives under mild reaction conditions with high regio‐ and stereoselectivtiy.     

Na2S–Carbon Nanotube Fabric Electrodes for Room‐Temperature Sodium–Sulfur Batteries

A unique sodium sulfide (Na₂S) cathode is developed, which will allow the use of sodium‐free anodes for room‐temperature sodium–sulfur (Na–S) batteries. To overcome the “inert” nature of the Na₂S, a special cathode structure is developed by spreading the multi‐walled carbon nanotube (MWCNT)‐wrapped Na₂S particles onto MWCNT fabrics. Spectroscopic and electrochemical analyses reveal a series of polysulfide intermediates involved in the charge/discharge of the cell. The Na–S battery prepared in full discharge state with the Na₂S/MWCNT cathode provides a remarkable capacity of 500 A h kg^?1 (based on sulfur mass) after 50 cycles.